|
| |
|
|
 |
Item
|
Item
|
Model
|
CI-125
|
|
SCREM DIA.
|
mm
|
36
|
40
|
45
|
|
INJ.
VOLUME
|
cm3/shot
|
148
|
182
|
231
|
|
INJ.
CAPACITY
|
g/oz
|
132/4.7
|
162/5.8
|
206/7.4
|
|
PLASTICIZING RATE
|
kg/hr (ps)
|
43
|
59
|
80
|
|
INJ. PRESS
|
kgf/cm2
|
2270
|
1840
|
1455
|
|
INJ.
STROKE
|
mm
|
145
|
|
SCREW
SPEED
|
rpm
|
145
|
|
NOZZLE
STROKE
|
mm
|
300
|
|
NOZZLE
FORCE
|
tonf(kN)
|
3.5(34)
|
|
CLAMP
FORCE
|
tonf(kN)
|
125(1225)
|
|
CLAMP
STROKE
|
mm
|
520
|
|
MIN.
THICKNESS
|
mm
|
200
|
|
DAYLIGHT
OPEN
|
mm
|
720
|
|
TIE BAR
DISTANCE
|
mm
|
420x420
|
|
PLATEN
SIZE
|
mm
|
607x607
|
|
EJECTOR
STROKE
|
mm
|
85
|
|
EJECTOR
FORCE
|
tonf(kN)
|
4.9(48)
|
|
OPENING FORCE
|
tonf(kN)
|
7.4(73)
|
|
MAX. SYS.
PRESS
|
kgf/cm2
|
170
|
|
MAX. SYS.
PRESS
|
kgf/cm2
|
18(25)/6
|
|
MOTOR POWER
|
kw(hp)/pole
|
15(20)/4
|
|
HEATER
CAPACITY
|
kw
|
8.3
|
|
HYD. OIL
REQ
|
L
|
340
|
|
MACHINE DIMENSIONS
|
(LxWxH) M
|
4.5x1.11x1.7
|
|
FLOOR
SPACE
|
M
|
3.88x1.05
|
|
FLOOR
SPACE
|
M
|
4.6
|
|
|
|
Clamping Unit:
|
|
Hydraulic clamping makes high-quality production
|
|
1.
The clamp distributes the pressure evenly. used for long-
term, it will never be twisted.
The tiebars are fixed securely
and will always rem ain perfectly parallel. Due
tathe fie bar
special design, the mold can move
very smoothly with
vitually little friction,
causing minimal stress or wear on the
bars on the molding.
|
|
2. The fast cylinder goes with the mold
into the low-pressure.
|
|
Injection Unit:
|
|
|
|
High ability of plasticizing, High
quality, High-speed molding
|
|
1.
The injection cylinder can rotate as well as move
linearly, So there is very little friction and
wear. It can be operated
very stable and quietly. With this machine, high-speed molding is
yours.
|
|
2. Adjust back pressure
with control of computer numericd unit.
|
|
3.
The operator can make fine funed
odjustments.
|
|
4.
CI-250,CI-300 adopt double cylinder design to shorten
machine length.
|
|
|
|
|
|
Single
injection cylinder
|
Dual
injection cylinder
|
|
|
Energy-saving means money-saving(option)
|
|
The
energy-saving pump meets pollution
|
|
requirements.
It works quietly and requires only 60%
|
|
of
the energy needed by fraditiond pumps.
|
|
|
Hydraulic unit:
|
|
Short-term cycle
|
|
The
oil tank is bosed on a brand-new design concept
|
|
to
apply oil to the cylinder for very high-speed
|
|
mavement, dlowing a very fast
production cycle.
|
|
|
|
Injection compression:
|
|
Low-pressure, In-mold compression, Low twist
|
|
|
|
Clamping
|
|
|
Direct hydraulic damping
|
|
|
True parallelism
between tie bars, high precision in find products
|
|
|
Strong platen,
constrain is minimized
|
|
|
Clamping for ce is evenly distibuted
|
|
|
Improved tie bar spacing to acccpt larger molds
|
|
|
Fix two end points,
maintain tie bar parallelism
|
|
|
Special tie bar
structure design, reduce central constroin.
|
|
|
High speed Oil tank.
|
|
|
Oil supply with minimum
friction.
|
|
Injection
|
|
|
Injection compression
for thin wall products
|
|
|
Injection, storage
|
|
|
2nd charge function
enable bigger capacity.
|
|
|
4 phose
injection, 3 phose pressure cssure
(changeable to 5 injection, 2 pressure)
|
|
|
3 phose
charge.
|
|
|
Auto purge.
|
|
|
Injection end pont setup
|
|
|
Cold start protection.
|
|
|
Injection end point
curve, injection precision statistic curve.
|
|
|
Display injection
precision.
|
|
|
Single cylinder
injection and charge motor in same axis.
|
|
|
Low injection &
charge friction.
|
|
|
Low friction between barrdl & screw enable best transparent plastic
injection.
|
|
|
Low noise.
|
|
|
Energy saving pump,
full utilization of energy, save up to 40%* opion*
|
|
Controller
|
Controller
|
|
|
Programmable
"STAR" controller, made in Japan
|
|
|
High resalution display
screen with various function display.
|
|
|
SPC parameter is easy
to set up & modify.
|
|
|
Monitor operation
procedure.
|
|
|
Instart display operation &
operation time.
|
|
|
Open, close mode & ejection.
|
|
|
Production management.
|
|
|
4 steps temperature
setup, expand to 6 steps.
|
|
|
Oil temperature display
in 1 section.
|
|
|
Oil prehcat function.
|
|
|
Thermo control curve.
|
|
|
100 SPC recard.
|
|
|
SPC precision
comparison.
|
|
|
Internal storage of 60
machine setup.
|
|
|
Display temperature
predision scale.
|
|
|
Pressure curve*,
Speedcurve*.
|
|
|
IC memory card to
expandstorage of machines setup*.
|
|
Programmable computer unit:
|
|
High efficiency and easy-to-use display
|
|
|
|
10" color screen (option)
|
|
|
The computer controller, made in
Japan with LCD display, is easy to use, operate, andset.
|
|
|
It is quick and simple
to call up the program to the LCD display for modification.
|
|
Injection/charge setting apge
|
Mould close/open setting page
|
|
|
|
|
Machine status page
|
Temperature setting page
|
|
|
|
|
|
|
|
|
|
High-speed cycle can
produce very thin-shelled products.
|
|
|
|
|
|
Holding evenly with
perfectly parallel platen.
|
|
|
|
|
|
High plasticizing and
good hold pressure
|
|
|
|
|
|
|
|
|
|
High speed Thin-wall
products.
|
|
We can offer, you the customer, a wide range of accessories to
complement your
|
We can offer, you the customer, a wide range
of accessories to complement your
|
|
injection machine. These accessories are
available locally and are manufactured to
|
|
the highest quality. Please see below for
what we can supply.
|
|
|
|
(Please Note: These accessories are not sold separately,
only with a Creator Machine)
|
|
Auto
Loaders
|
Conveyors
|
|
Hopper
Dryers
|
Chillers
|
|
Dust
Collectors
|
Dehumidifiers
|
|
Robots
|
Mould
Temperature Controllers
|
|
Moulds
|
Oven
Dryers
|
|
Granulators
|
Masterbatch
|
|
|
|
|
 |
|
|
